Allegion Developer Portal
Allegion Developer Portal
AD-400 APM Address 1
PIM-400-485-400 RSD Address 3
The Message Bytes column in Table 14-3 shows the first three bytes without the Start and CRC bytes. These are Address, Message Type, and Message Length.
NOTE: The use of Bold, Italic and Bold Italic font is to show the difference in the first three bytes within the table.
| Message Bytes | Command Type/ Address | Decoded Message | Notes |
|---|---|---|---|
| 03 3A 00 | RSD/0x03 | Address = 3, POLL_RSD_CRC, Lngth = 0 | Standard poll message. |
| FF 31 0A 01 01 00 11 00 1A 99 00 02 C1 | 0xFF | Address = 255, RSD_STATUS_CARDDATA, Lngth = 10, Byte 1 Bits 0 - 7: APM Address (0x00 to 0xFE excluding 0xAA) =>0x01 (1) Byte 2 Bit 0: Reader Tamper;1=Tamper =>1 Bit 1: Low Battery;1=Low Battery =>0 Bit 2: Loss of RF Communications;1=RF loss =>0 Bit 3: RSD Tamper;1=RSD door is open =>0 Bit 4: Cache Status;1=has been used =>0 Bit 5: Motor Stall;1=Motor is Stalled =>0 Bit 6: Lock Clutch Position;1=door unlocked =>0 Bit 7: Deadbolt Position;1=bolt extended =>0 Byte 3 Bit 0: Request To Exit Active;1=REX Active =>0 Bit 1: APM forced;1=Forced APM =>0 Bit 2: APM Open Too Long;1=APM Open Too Long =>0 Bit 3: Tamper Active;1=Tamper Active =>0 Bit 4: Datalog Ready; =>0 Bit 5: Configuration Mode;1=In Configuration Mode =>0 Bit 6: RSD/APM is in Link Mode;1=Link mode Enabled =>0 Bit 7: AD-400 Battery Critical/AD-300 REN Active;1=True =>0 (cont’d) | Response gives status of a 26-bit card. In this case, a Prox card presented to the AD-400 at APM Address 1 connected to PIM-400-485 with RSD Address 3. |
| Byte 4 Bit 0: Trouble;1=APM has trouble =>1 Bit 1: AD-400 Low Li Battery/AD-300; 1=Low Battery =>0 Bit 2: Door Position Switch;1=closed =>0 Bit 3: IPB;1=IPB Pressed =>0 Bit 4: Request To Exit Switch;1=inactive =>1 Bit 5: Wireless: Request to Enter Switch/VIP:LBM Status;1=Active/BoltExtended =>0 Bit 6: Key Override;1=key being used =>0 Bit 7: Lock State;1=unlocked, 0=locked =>0 Byte 5 Bits 0 - 7: More Events =>0x00 (0) Byte 6 Bits 0 - 7: Card data bit count =>0x1A (26) Byte 7 Bits 0 - 7: Card data read at APM =>0x99 (153) Byte 8 Bits 0 - 7: Card data read at APM =>0x00 (0) Byte 9 Bits 0 - 7: Card data read at APM =>0x02 (2) Byte 10 Bits 0 - 7: Card data read at APM =>0xC1 (193) | |||
| 01 4F 01 03 | APM/0x01 | Address = 1, APM_LOCK_CONTROL, Lngth = 1 Byte 1 Bits 0-7: Output state; 3=Re-lock => 0x03 (3) | It is a bit unnecessary to send the relock since the door is already locked, but this will indicate to the user immediately that the card presented was denied instead of waiting for the timeout period. |
| FF 30 03 01 00 11 | 0xFF | Address = 255, APM_STATUS, Lngth = 3 Byte 1 Bit 0: Reader Tamper;1=Tamper =>1 Bit 1: Low Battery;1=Low Battery =>0 Bit 2: Loss of RF Communications;1=RF loss =>0 Bit 3: RSD Tamper;1=RSD door is open =>0 Bit 4: Cache Status;1=has been used =>0 Bit 5: Motor Stall;1=Motor is Stalled =>0 Bit 6: Lock Clutch Position;1=door unlocked =>0 Bit 7: Deadbolt Position;1=bolt extended =>0 Byte 2 Bit 0: Request To Exit Active;1=REX Active =>0 Bit 1: APM forced;1=Forced APM =>0 Bits 2 - 3: Reserved; =>0 Bit 4: Datalog Ready; =>0 Bit 5: Configuration Mode;1=In Configuration Mode =>0 Bit 6: RSD/APM is in Link Mode;1=Link mode Enabled =>0 Bit 7: AD-400 Battery Critical/AD-300 REN Active;1=True =>0 Byte 3 Bit 0: Trouble;1=APM has trouble =>1 Bit 1: AD-400 Low Li Battery/AD-300 Data;1=Low Battery =>0 Bit 2: Door Position Switch;1=closed =>0 Bit 3: IPB;1=IPB Pressed =>0 Bit 4: Request To Exit Switch;1=inactive =>1 Bit 5: Wireless: Request to Enter Switch/VIP:LBM Status;1=Active/BoltExtended =>0 Bit 6: Key Override;1=key being used =>0 Bit 7: Lock State;1=unlocked, 0=locked =>0 |